3-Inch vs 5-Inch Ball Vise: Jaw Opening & Bench Fit
When an engraving vise looks right but leaves too little room around your hands, the problem may be its size rather than your technique. Choose around the workpiece, holders and bench arrangement—not the biggest number in the product title.

Start with three different measurements
Ball diameter describes the main spherical body. Maximum jaw opening describes the gap available between the jaws. Installed height describes how much room the base and ball occupy above the bench. These measurements answer different questions, and none alone proves that an irregular workpiece can be held securely.
View the 3-inch ball configuration · View the 5-inch ball configuration. Confirm the selected SKU and current availability on the product page.
Compare the exact VEVOR models
| Specification | Compact selection | Larger selection |
|---|---|---|
| Model | JH-N3YC001BP | JH-N5YC001BP |
| SKU | WNXZSZ213YC314SIPV0 | WNXZSZYHDGW337TS8V0 |
| Listed ball diameter | 3 in / 78 mm | 5 in / 127 mm |
| Maximum opening in specification table | 2.13 in / 54 mm | 3.86 in / 98 mm |
| Maximum installed size | 3.8 × 3.8 × 3.3 in / 97 × 97 × 85 mm | 5.7 × 5.7 × 6.7 in / 145 × 145 × 170 mm |
| Listed weight, including accessories | 4.4 lb / 2 kg | 20.3 lb / 9.2 kg |
| Base material | Reinforced plastic | Rubber |
| Jaw / ball material and finish | Steel; chrome plating | Steel; chrome plating |
Opening-label discrepancy: the larger variant is named “3.93inch,” while its detailed specification says 3.86 inches / 98 mm. Do not treat the option label as a guaranteed extra allowance. If your holder is close to the limit, request confirmation of usable opening for the exact shipped SKU.
When to consider the compact model
Start with JH-N3YC001BP when bench space and moving the vise between workstations matter. Its listed installed envelope is smaller, and the listed weight with accessories is lower. Those figures help with planning; they are not a workpiece weight rating.
Make a paper outline of the listed footprint on your bench. Add space for your hands, tools and the workpiece as you turn it. If you use a microscope, check the height of the actual work surface after the jaws, holders and workpiece are in place. The vise's overall height is only one part of that stack.

When to consider the larger model
Consider JH-N5YC001BP when the compact model's opening or physical size does not suit your planned holder. Allow for its taller installed envelope and heavier listed kit when deciding where it will live. A larger ball does not automatically mean better results for every small item.
Before buying, sketch the whole setup: bench surface, base, vise, holder and workpiece. Check whether the taller arrangement changes your seated posture or tool access. For shared benches, decide where the vise can be stored without leaving an awkward lift for the next session.

Check how the workpiece will be held
Measure the holder as well as the item. Pins, pads and clamps can reduce the usable space between the jaws. An item that fits the nominal gap may still need a different holding arrangement to keep the working area accessible.
Use a nonvaluable practice piece to assess your chosen setup before working on finished jewelry. Follow the model manual for adjustment and clamping; this guide does not specify a clamping torque, load rating or gemstone-setting procedure.
Resolve the accessory wording before ordering
The product options say “No Special Accessories,” while supplier titles and photographs describe attachment sets. This wording does not establish an itemized box list or prove that the separate ring-exclusive option is included. Ask for a SKU-specific packing list covering the holders you need, their quantities and compatibility.

Before you order
- Match the model and SKU to the configuration you intend to buy.
- Measure workpiece and holder width, rather than comparing ball diameter alone.
- Confirm usable opening if your setup is near the larger model's conflicting size labels.
- Check footprint, installed height and room to rotate the workpiece.
- Request an itemized accessory list and verify any specialized ring holder.
- Check current price, delivery eligibility and availability on Dekuch.
Frequently asked questions
Does a 5-inch ball mean a 5-inch jaw opening?
No. The larger model has a listed 5-inch ball diameter and a specification-table opening of 3.86 inches / 98 mm.
Does the listed weight describe the vise alone?
The current source labels these weights as including all accessories. Do not use them as machine-only or packaged shipping weights.
Can I assume every shown attachment is supplied?
No. Confirm the packing list for your SKU, especially where the option name and descriptive accessory claims differ.
Will either model fit under my microscope?
Check the complete working-height stack and the microscope's clearance. Product dimensions alone cannot confirm that fit.
Choose around the actual work
Compare the current VEVOR engraving ball vise selections at Dekuch. If the holder or accessory list is unclear, ask before ordering.
For other bench tools, see the ring engraving character-size guide and 3-inch bench buffer guide, or browse the VEVOR buying-guide hub.
Sources
VEVOR compact SKU specifications · VEVOR larger SKU specifications. Checked October 26, 2026.